Timewave Port Devices Driver Download For Windows 10



The CH340 chip is used by a number of Arduino compatible boards to provide USB connectivity, you may need to install a driver, don’t panic, it’s easier than falling off a log, and much less painful.

Signed Windows FTDI Drivers for Navigator Download the Navigator Windows FTDI drivers here. (Windows XP, Vista, Windows 7, Windows 8, 32 & 64 bit) Navigator ONLY! Not for HamLinkUSB devices! Nav-TW Driver 2416.zip (6 MB) Mac FTDI Drivers for Navigator Download and read the file entitled 'MAC Readme' Mac Drivers (700 K). Navigator FTDI COM Port Drivers. Navigator Setup and Drivers for Windows - 2016. Signed driver set for the Timewave Navigator. Win XP, Vista, Win 7, Win 8/8.1, Win 10 (32 & 64 bit) Note: These are for the Navigator only! ExtFSK for MTTY, WinWarbler and N1MM+ Navigator Setup and Drivers for Windows - 2016.zip Nav-TW Driver 20420.zip. Drivers & Downloads. Locate drivers, user guides and product specifications for your Gateway technology. Get support via your Windows 10 device Learn.

The device's wave port and miniport drivers appear at the lower-right corner of the figure. As shown in the figure, the port driver receives as input the stream from the miniport driver and outputs it either directly to the user-mode DirectSound component, Dsound.dll, or indirectly through KMixer. All devices operating in MTP mode are supported. Note: The MTPdrive is not a replacement for the device's factory (or Windows default) device driver. You must be able to connect your device to the computer and have it visible in the Windows Explorer, before it can be mapped as a drive letter using the MTPdrive.


Timewave Port Devices Driver Download For Windows 10 7

Windows

(Manufacturer’s Chinese Info Link)

  1. Download the Windows CH340 Driver
  2. Unzip the file
  3. Run the installer which you unzipped
  4. In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.

Older Windows Driver Version and Instructions

  1. Download the Windows CH340 Driver
  2. Unzip the folder.
  3. If you are running a 64Bit Windows: – run the SETUP_64.EXE installer.
  4. If you are running a 32Bit Windows: – run the SETUP_32.EXE installer.
  5. If you don’t know, try the 64 bit and if it doesn’t work, the 32 bit.
  6. In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.

Macintosh

(Manufacturer’s Chinese Info Link)

The following github has up to day pkg files for 1.3, 1.4 and 1.5 at time of writing, thanks to Joshua Wallis for bringing this to my attention…

Direct Download Links (from the github repo above):

See the github link above for installation instructions if you need them.

Previous macinstosh downloads if the above doesn’t work for you…

(V1.3) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11) and Sierra (10.12)

Inside the zip file you will find a PDF and a “pkg” file, short version, double click the pkg file, the PDF has some extra information.

OSX Sierra (10.12) Note

A kindly user, Maarten Segers reports

Timewave Port Devices Driver Download For Windows 10 32-bit

FYI, the driver documented here WILL crash on OSX Sierra.

Make sure to use this one instead: https://github.com/MPParsley/ch340g-ch34g-ch34x-mac-os-x-driver

I can personally not test on MacOS and can not vouch for the above drivers at github, but there you go.

See uninstalling information at the bottom of the page if the driver causes problems for you.

Here is an older version of the Mac driver, NOT FOR 10.12 Sierra

(V1.0) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11)

Linux

Timewave port devices driver download for windows 10 7

(Manufacturer’s Chinese Info Link)

Drivers are almost certainly built into your Linux kernel already and it will probably just work as soon as you plug it in. If not you can download the Linux CH340 Driver (but I’d recommend just upgrading your Linux install so that you get the “built in” one).

Port

Uninstalling From Macinstosh

A couple of Mac users have said “the driver crashes my mac Sierra how do I uninstall”.

Firstly regards the crash make sure you installed the 1.3 version of the driver, not the old one. You could download it directly from the Manufacturers Website in case they have issued an update since I wrote this page.

Secondly a quick google search reveals that this is how you uninstall:

Timewave Port Devices Driver Download For Windows 10
  1. Open a terminal and type: cd /Library/Extensions/
  2. Verify that the .kext file is present: ls | grep usbserial.kext
  3. Output should be: usbserial.kext
  4. Then type: sudo rm -R usbserial.kext
  5. Verify that the .kext file has been removed: ls | grep usbserial.kext
  6. Output should be empty.
  7. After you should remove the files stored in receipts folder: cd /private/var/db/receipts/
  8. Find the enties: ls | grep usbserial*
  9. Output should be: codebender.cc.ch34xinstaller.usbserial.pkg.bom codebender.cc.ch34xinstaller.usbserial.pkg.plist
  10. Remove each one of the files of the above list: sudo rm -r filename`

Day/Night Always-Visible Display
Day or night, the Timewave TZ-900 AntennaSmith™ is a bright colorful window to your antenna system. The transreflective TFT LCD color display is brilliantly visible in direct sunlight - no lost data from a washed-out display!

Full Graphics - Rapid update
The AntennaSmith™'s rapid sweep updates the data graph every two seconds. Quickly set the start, stop or center frequencies to see the data as you want it. A tap on a button gives you a different parameter. Tap another button to store a graph to print later or to display as a reference while you optimize your antenna system. Instantly see the effect of an adjustment or a change! No computer connection is required to see all the graphs - even the Smith chart!

Adjustable Frequency Cursor/Generator
Quickly tune the cursor to check your antenna system at the desired frequency while looking at the big picture on a graph. The Direct Digital Synthesizer makes a great RF signal generator in the Synthesizer mode. Easily calibrate to WWV with 1 Hz frequency resolution.

Data Comparison & Remote Control Software
The included Windows program lets you display, compare and export your data. Use your PC or laptop to run the AntennaSmith™ for quick printed reports.

Rugged and Portable
The AntennaSmith™ has a rugged extruded aluminum case and batteries for hours of field operation. A 12 VDC power supply/ charger (117VAC/60Hz) is included.